High-speed steel rolls are suitable for high-speed rolling processes, which can meet the needs of bar rolling mills for high-speed and efficient production and improve production efficiency. It can withstand the friction and wear of metal materials during high-speed rolling and extend the service life of the roll. It has high thermal conductivity and can quickly transfer heat to the roll surface, helping to control the temperature during the rolling process and improve rolling efficiency. It has good mechanical strength and impact resistance and can withstand the high pressure and impact load generated by metal materials during high-speed rolling. The use of high-speed steel rollers in bar rolling mills can improve production efficiency, reduce production costs, and ensure that the rolled bar products have surface quality and dimensional accuracy. Therefore, they have been widely used in the bar rolling industry.
Hardness HSD: 75-95
Nickel composition %: 0-1.5
Suitable for racks: Finishing rolls, pre-finishing rolls
Usage: Hot strip and bar finishing roll; section universal mills;pre-finishing stands of high-speed wire mill.
| Chemical Composition % | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| Symbol | C | Si | Mn | Cr | Ni | Mo | V | W | P | S |
| HSS | 1.50-2.20 | 0.30-1.0 | 0.40-1.20 | 3.00-8.00 | 0.00-1.50 | 2.00-8.00 | 2.00-9.00 | 0.00-8.00 | ≤0.03 | ≤0.025 |
| S-HSS | 0.60-1.20 | 0.80-1.50 | 0.50-1.00 | 3.00-9.00 | 0.20-1.20 | 2.00-5.00 | 0.40-3.00 | 0.00-3.00 | ≤0.03 | ≤0.025 |
| Prosperities & Application | |||||||
|---|---|---|---|---|---|---|---|
| Symbol | Hardness | Size | Application | ||||
| HSD | |||||||
| HSS | 75-95 | ¢300~700 | Hot strip and bar finishing roll;section universal mills;pre-finishing stands of high speed wire mill. | ||||
| S-HSS | 75-85;80-98 | ||||||
HSS Mill Rolls take their name from high-speed tool steel, and they borrow its microstructure. Alloying elements such as vanadium, molybdenum, tungsten, and chromium form very hard carbides that are spread through a tempered matrix. These carbides are harder than the ones found in conventional chromium or chilled iron rolls, which is why the roll face wears far more slowly.
Working hardness spans 75-95 HSD, at the top of the hardness scale used for mill rolls, and nickel is kept low at 0-1.5% because the performance comes from the carbide system rather than from nickel alloying. The wide range lets the roll be tuned to the stand: higher for pure wear duty, lower where toughness is more important.
In bar rolling, where speeds continue to climb, this carbide structure lets the roll keep its groove shape and surface condition noticeably longer than conventional materials.
The carbide-rich surface slows groove wear, so a single roll campaign can handle significantly more tonnage and the groove profile stays closer to its design.
Slow, even wear keeps cross-section stable from the start to the end of the campaign, so bar diameter, ovality, and shape stay within tolerance with fewer adjustments.
A hard, uniform groove surface is less prone to roughening, which reduces marks transferred to the product.
At high rolling speed, the roll is exposed to rapid heating and cooling. The grade keeps its hardness at working temperature and resists surface damage, helping the roll maintain performance throughout the campaign.
Longer campaigns mean fewer stand changes and less regrinding stock removed. Even though an HSS roll costs more upfront, its cost per ton rolled can be lower.
HSS rolls are placed where speed, wear, and precision matter most:
The final passes set diameter and surface. A wear-resistant HSS roll keeps both stable at high speed.
Stands ahead of the finishing block carry high loads and see heavy wear. HSS rolls hold groove geometry so the stock entering the finisher is consistent.
Wire mills run at very high speed with small grooves, a duty where carbide hardness delivers the greatest gains.
In hot strip finishing, surface and gauge consistency matter; in universal section mills, complex contact conditions benefit from the roll's even wear.
Hardness within 75-95 HSD, barrel size, and groove design should be matched to stand position, rolling speed, and cooling. In demanding positions like these, HSS Mill Rolls deliver the most when the stand is well maintained.
Hardness and wear resistance come mainly from vanadium, molybdenum, tungsten, and chromium carbides, not from nickel. Low nickel is normal for this roll type.
They are designed for finishing and pre-finishing duty. Roughing stands face heavy impact and thick stock, where tougher roll materials are usually safer.
Keep cooling water even and sufficient, avoid thermal shock during stops, handle rolls carefully, and regrind on a schedule. These steps help HSS Mill Rolls keep their hardness and surface.