We use cookies to offer you a better browsing experience, analyze site traffic and personalize content. By using this site, you agree to our use of cookies. Privacy Policy
Home / Product / Semi-High Speed Steel Rolls Grade (S-HSS) for Hot Strip Work Roller

Semi-High Speed Steel Rolls Grade (S-HSS) for Hot Strip Work Roller

Return to product list

PRODUCT INTRODUCTION

The hardness range of semi-high-speed steel rolls is usually between HSD 75 and 98. Rolls with different hardness can be selected according to different rolling processes and metal material requirements. The nickel content is between 0.2% and 1.2%. Nickel is a common alloying element that can increase the strength and hardness of steel, while also improving the corrosion resistance and thermal stability of steel. It is suitable for various rolling processes such as roughing, intermediate rolling, and finishing rolling, and can meet the rolling needs of different metal materials, including steel, aluminum, etc. Semi-high-speed steel rollers have high strength and hardness, can withstand the rolling process under high pressure and high speed, and have good wear resistance, extending the service life of the rolls. Semi-high-speed steel rolls are widely used in various metal rolling processes due to their wide hardness range, wide application range, high strength, and wear resistance. They are an important rolling equipment.

Hardness HSD: 75-98

Nickel composition %: 0.2-1.2

Suitable for racks: Rough-medium rolled, finish rolled

Contact Us

PRODUCT SPECIFICATIONS

High-Speed Steel Rolls (HSS)

Chemical Composition %
Symbol C Si Mn Cr Ni Mo V W P S
HSS 1.50-2.20 0.30-1.0 0.40-1.20 3.00-8.00 0.00-1.50 2.00-8.00 2.00-9.00 0.00-8.00 ≤0.03 ≤0.025
S-HSS 0.60-1.20 0.80-1.50 0.50-1.00 3.00-9.00 0.20-1.20 2.00-5.00 0.40-3.00 0.00-3.00 ≤0.03 ≤0.025

 

Prosperities & Application
Symbol Hardness Size Application
HSD
HSS 75-95  ¢300~700 Roughing work rolls for hot strip mill;work rolls and intermediate rolls of cold strip mills
S-HSS 75-85;80-98

 

 

A Bridge Between High Chromium and Full HSS

S-HSS is built on the same carbide-strengthening idea as high speed steel, but with a more moderate alloy balance. The result sits between conventional high chromium iron and full HSS: more wear resistance than the former, and better toughness and lower cost than the latter. For mills that run varied duty across the hot strip line, Hot Strip Mill Work Rolls in this category offer flexibility that a single extreme grade cannot.

Hardness covers a wide span, 75-98 HSD, so the same material family can be specified for stands with very different needs. Nickel at 0.2-1.2% adds matrix strength and supports hardenability without driving up cost.

Lower-hardness versions emphasize toughness for the heavier early stands, while higher-hardness versions emphasize wear life and surface retention in the finishing stands.

Core Advantages

Roll surface that lasts

A carbide-strengthened surface wears slowly, so strip surface quality stays stable over a longer rolling distance before a work roll change is needed.

Toughness for the real world

Hot strip stands see bite shocks, strip tails, and occasional cobbles. Moderate alloying leaves the roll with more tolerance for these events than a fully loaded HSS design, lowering the risk of surface spalling or breakage.

Gauge and flatness control

Even wear preserves roll profile, so thickness, crown, and flatness remain close to target through the campaign, with fewer corrections.

Resistance to thermal fatigue

Work rolls are heated by strip and cooled by water on every revolution. The grade resists the buildup of fine thermal cracks, so surfaces remain smooth and roll life is not cut short by surface cracking.

Value in balance

Longer life than conventional work rolls at a lower price than full HSS gives a strong cost-per-ton result, especially in stands where extreme hardness is not necessary.

Stand-by-Stand Use in the Hot Strip Line

Because the hardness range is wide, S-HSS can follow the strip through the line:

Roughing and rough-medium stands

Heavy reductions and thick, hot stock call for strength and impact tolerance. Choose the lower end of the hardness range here.

Early finishing stands

Loads are still high, but surface quality starts to matter. Mid-range hardness balances wear life with the ability to absorb shock.

Late finishing stands

Final thickness and surface are set here. Higher hardness extends the period of stable surface, and consistent roll profile protects strip flatness.

Choice of hardness, barrel size, and surface finish should reflect stand position, reduction schedule, product mix, and cooling system. A well-matched specification helps Hot Strip Mill Work Rolls deliver stable strip quality across the whole campaign.

Q&A

Q1: What does "semi" mean in semi-high speed steel?

It indicates a lower alloy content than full high speed steel, which reduces cost and improves toughness while keeping much of the wear resistance of carbide-rich materials.

Q2: Can S-HSS replace high chromium work rolls?

In many stands it can, particularly where longer campaigns or better surface retention are wanted. The decision depends on stand duty and economics, and trial results on your own line are the best guide.

Q3: How do I choose the hardness within 75-98 HSD?

Start with stand position: lower for roughing and early finishing, higher for late finishing. Reduction, speed, cooling, and product requirements refine the choice. Matching hardness to duty is what lets Hot Strip Mill Work Rolls reach their full potential.

Send Us a Message

We'll get back to you within 24 hours with a tailored solution for your rolling mill.
captcha