We use cookies to offer you a better browsing experience, analyze site traffic and personalize content. By using this site, you agree to our use of cookies. Privacy Policy
Home / Product / Adamite Rollers Grade 180 (AD180)for Roughing Stand

Adamite Rollers Grade 180 (AD180)for Roughing Stand

Return to product list

PRODUCT INTRODUCTION

The hardness and wear resistance of Adamite Rollers 180 are higher than those of cast iron rolls, and their strength and toughness are better than those of cast steel rolls. They can withstand greater impact loads and are not easy to break, improving the safety and stability of the rolling mill. The hardness range of HSD 45-60 is suitable for roughing frames and can meet the requirements for roll hardness during roughing. The addition of nickel can increase the strength, toughness, and wear resistance of Adamite Rollers, and improve their thermal fatigue and corrosion resistance. Semi-steel rolls used for roughing stands are widely used in roughing stands of various roughing mills and blooming mills, including hot rolling mills, cold rolling mills, special steel rolling mills, etc. It has good thermal fatigue resistance and can withstand shock and vibration under high temperatures and pressure.

Hardness HSD: 45-60

Nickel composition %: 0.5-2.0

Suitable for racks: Chinese steel rolling

Contact Us

PRODUCT SPECIFICATIONS

Adamite Rolls (AD)

Chemical Composition % 
Symbol C Si Mn Cr Ni Mo P S
AD140 I 1.30-1.50 0.30-0.60 0.70-1.10 0.80-1.20 0.50-1.20 0.20-0.60  ≤0.035 ≤0.030
AD160 I 1.50-1.70 0.30-0.60 0.80-1.30 0.80-2.00 ≥0.20  0.20-0.60 ≤0.035 ≤0.030
AD180 1.70-1.90 0.30-0.80 0.60-1.10 0.80-3.50 0.50-2.00  0.20-0.60 ≤0.035 ≤0.030
AD200 1.90-2.10 0.30-0.80 0.80-1.20 0.60-2.00 0.60-2.50 0.20-0.80 ≤0.035 ≤0.030

 

Prosperities & Application
Symbol Hardness Application
HSD
AD140 I 35-45;40-50 Roughing stands of section, bar, and wire mills; large, medium section, rail, steel blank, section universal mills; hot strip roughing rolls, backup rolls, and edger rolls.
AD160 I 40-50;50-60
AD180 45-55;50-60
AD200 50-60;55-65

 

A Tunable Grade for the First Stands

The first stands of a rolling line receive the thickest, hottest, and least uniform stock. Scale, uneven temperature, and large reductions arrive together, and the roll has to absorb them day after day. AD180 is a semi-steel grade developed for that environment, and it is a practical choice among Roughing Stand Rolls when toughness cannot be compromised.

Two specification windows give mills room to tune the roll. Hardness spans 45-60 HSD, so a softer setting can be selected for severe impact and a firmer one where abrasion dominates. Nickel spans 0.5-2.0%, allowing the matrix strength and toughness to be set to suit the stand's loading and the mill's rolling schedule.

Both ranges reflect a single principle: in roughing, the roll's first duty is to survive heavy loads without cracking, and its second is to wear slowly.

Key Advantages

Fewer breakages

A strong, tough body carries heavy rolling force and absorbs impact from irregular billets, reducing the risk of cracks growing into roll failure.

Less surface spalling

Moderate hardness and a well-supported working layer resist flaking under pressure and thermal cycling, keeping the surface usable longer.

Resistance to thermal damage

Roughing rolls spend long periods in contact with very hot stock. The grade tolerates repeated heating and water cooling with limited surface cracking.

Controlled wear

Steady, predictable wear keeps pass dimensions in range for the entire campaign, so downstream stands receive consistent material.

Planned, economical operation

Strong roll life means scheduled changes rather than emergency ones, and a moderate material cost gives a low cost per ton rolled.

Application Scenarios

AD180 is applied wherever primary reduction takes place:

Blooming and slabbing mills

The heaviest reductions in the line need maximum toughness. The roll's strength and thermal tolerance suit this duty.

Hot rolling roughing stands

In hot strip and plate roughing, the roll must break down thick slabs consistently, and even wear helps keep downstream gauge control stable.

Special steel mills

Alloy and special steels resist deformation and raise rolling loads. A tough roll with good thermal fatigue resistance is a safer choice.

Other roughing positions

Mills in which the first stands break down billets and slabs can use the grade, with groove or barrel design matched to the product.

Hardness within 45-60 HSD, nickel content, and barrel size should be matched to stand position, billet size, and rolling schedule. Specifying Roughing Stand Rolls with these factors in mind helps the roll deliver stable service life.

Q&A

Q1: Why is the hardness not higher for roughing?

Heavy impact and thick stock make very hard rolls prone to chipping. A moderate hardness protects against damage while still giving useful wear life.

Q2: What does nickel do in this grade?

Nickel strengthens the matrix and improves toughness and hardenability, helping the roll handle load and thermal cycling. A wider range allows adjustment to the duty.

Q3: Can the roll be reground and reused?

Yes. Moderate hardness is easy to machine, and regrinding removes surface fatigue and restores the profile. Good regrinding practice helps Roughing Stand Rolls reach a full service life.

Send Us a Message

We'll get back to you within 24 hours with a tailored solution for your rolling mill.
captcha