We use cookies to offer you a better browsing experience, analyze site traffic and personalize content. By using this site, you agree to our use of cookies. Privacy Policy
Home / Product / Hardness 50-65HSD Adamite Rollers Grade 200 (AD200)

Hardness 50-65HSD Adamite Rollers Grade 200 (AD200)

Return to product list

PRODUCT INTRODUCTION

Adamite rolls consist of a cast iron outer layer and a steel core. The cast iron outer layer provides better wear resistance, while the steel core provides higher strength and hardness. The wear resistance of the cast iron outer layer enables the semi-steel roll to withstand the friction and wear of the metal blank, extending the service life of the roll. Compared with all-steel rolls and other materials, Adamite Rollers 200 (AD200) have lower manufacturing costs, but their performance can still meet the requirements of the rolling process and have good cost-effectiveness. It is suitable for various rolling mill equipment, including rough rolling mill, intermediate rolling mill finishing rolling mill, etc., and can meet the rolling needs of metal billets of different sizes and materials.

Hardness HSD: 50-65

Nickel composition %: 0.6-2.5

Suitable for racks: pre-finishing

Contact Us

PRODUCT SPECIFICATIONS

Adamite Rolls (AD)

Chemical Composition % 
Symbol C Si Mn Cr Ni Mo P S
AD140 I 1.30-1.50 0.30-0.60 0.70-1.10 0.80-1.20 0.50-1.20 0.20-0.60  ≤0.035 ≤0.030
AD160 I 1.50-1.70 0.30-0.60 0.80-1.30 0.80-2.00 ≥0.20  0.20-0.60 ≤0.035 ≤0.030
AD180 1.70-1.90 0.30-0.80 0.60-1.10 0.80-3.50 0.50-2.00  0.20-0.60 ≤0.035 ≤0.030
AD200 1.90-2.10 0.30-0.80 0.80-1.20 0.60-2.00 0.60-2.50 0.20-0.80 ≤0.035 ≤0.030

 

Prosperities & Application
Symbol Hardness Application
HSD
AD140 I 35-45;40-50 Roughing stands of section, bar, and wire mills; large, medium section, rail, steel blank, section universal mills; hot strip roughing rolls, backup rolls, and edger rolls.
AD160 I 40-50;50-60
AD180 45-55;50-60
AD200 50-60;55-65

 

 

Built for the Middle of the Line

Pre-finishing stands sit in an awkward place. They no longer take the brutal reductions of roughing, yet they carry heavier loads than the finishing stands, and the stock they deliver sets up the quality of the final passes. Adamite Cast Steel Rolls at a hardness of 50-65 HSD are designed for this middle ground, and AD200 is the grade that gives it practical shape.

The hardness window sits above typical roughing grades, trading a little toughness for longer-lasting surfaces. Nickel at 0.6-2.5% gives the matrix room for strength and thermal stability, so the roll can handle load and heat cycling while keeping its profile.

The result is a roll that does not need to be as soft as a breakdown roll nor as hard as a finishing roll: it is tuned for steady load, moderate wear, and good dimensional behavior.

What AD200 Offers

Balanced hardness

A working hardness of 50-65 HSD resists wear without becoming sensitive to the shocks that still occur in pre-finishing.

Dimensional consistency

Slow, even wear holds groove or barrel geometry close to target, and the stock delivered to the finishing stands arrives with consistent size and shape.

Thermal stability

The grade keeps its shape and surface under repeated heating and cooling, limiting fine thermal cracks and distortion.

Surface condition

A uniform working layer wears evenly, so the surface passed to the product stays cleaner for longer.

Economic rolls for mid-line duty

Pre-finishing stands do not need premium roll materials. AD200 provides the performance the duty requires at a moderate cost, with fewer changes and a lower cost per ton.

Wide nickel range

With nickel from 0.6% to 2.5%, specification can be adjusted toward more toughness or more hardenability depending on how severe the stand is.

Choosing AD200 by Duty

Good fit

Pre-finishing stands where loads are significant but not extreme, product dimensions are tight, and a long campaign is valuable. This includes mills that roll steel billets of different sizes and materials with groove layouts matched to each product.

Possible fit

Intermediate stands and, in some cases, finishing positions with steady load, provided surface demands are not extreme. Hardness toward the upper end of the range is better for these.

Consider another grade

Heavy roughing stands with severe impact are better served by a tougher, lower-hardness roll, while the most demanding finishing stands may need a harder grade such as chilled iron, high chromium, or HSS.

Barrel size, hardness within 50-65 HSD, and nickel content should be specified with stand position, product range, and cooling conditions in mind. For this kind of mid-line duty, Adamite Cast Steel Rolls offer a sensible balance of wear life, strength, and cost.

Q&A

Q1: What makes adamite different from ordinary cast steel?

Adamite carries more carbon than plain cast steel, forming carbides that raise wear resistance while the matrix stays strong. This gives longer life in abrasive service, with better toughness than hard cast iron.

Q2: Why is AD200 suited to pre-finishing rather than roughing?

Its hardness is higher than that of roughing grades, so it resists wear better but tolerates less shock. Pre-finishing stands see steadier loads, which is where that balance works best.

Q3: How can I get the most from the roll?

Maintain even cooling, correct alignment, and timely regrinding. Checking the surface for early fatigue lets Adamite Cast Steel Rolls run to the end of their campaign without surprises.

Send Us a Message

We'll get back to you within 24 hours with a tailored solution for your rolling mill.
captcha