High-strength alloy cast steel roll 65I is a type of roll used in rough rolling applications. Rough rolling is the initial stage of the rolling process where the steel is reduced in cross-sectional area. Alloy cast steel rollers are tercih [preferred] for rough rolling because they are very hard and resist wear. The hardness of a 65I roll is HSD 35-45, which is high on the Rockwell C scale of hardness. these rolls are very hard and resist wear, which is important in rough rolling where the steel is being significantly deformed. This can help to reduce roll wear and replacement costs. can withstand the high temperatures that are generated during rough rolling. These rolls maintain their shape well during rolling, which helps to produce high-quality steel products.
Hardness HSD: 35-45
Nickel composition %: 0.2-0.5
Suitable for racks: roughing
Usage: Section roughing mills, bar, and wire roughing mills; rail, section universal blooming mills; hot strip breaker and rougher; plate roughing rolls; backup rolls for the strip, edger rolls.
| Chemical Composition % | ||||||||
|---|---|---|---|---|---|---|---|---|
| Symbol | C | Si | Mn | Cr | Ni | Mo | P | S |
| AS65I | 0.60-0.70 | 0.20-0.60 | 0.50-0.80 | 0.80-1.20 | 0.20-0.50 | 0.20-0.45 | ≤0.035 | ≤0.030 |
| AS70II | 0.65-0.75 | 0.20-0.45 | 1.40-1.80 | - | - | 0.20-0.45 | ≤0.035 | ≤0.030 |
| AS75I | 0.70-0.80 | 0.20-0.70 | 0.70-1.10 | 0.80-1.50 | ≥0.20 | 0.20-0.60 | ≤0.035 | ≤0.030 |
| Prosperities & Application | ||
|---|---|---|
| Symbol | Hardness | Application |
| HSD | ||
| AS65 I | 35-45 | Section roughing mills, bar and wire roughing mills; rail, section universal blooming mills; hot strip breaker and rougher; plate roughing rolls; backup rolls for strip, edger rolls. |
| AS70 II | 35-45 | |
| AS75 I | 35-45;40-50 | |
In the opening stands of a rolling line, a roll that fails costs far more than a roll that wears. Cast steel answers that risk directly. Its fine, continuous matrix resists crack growth better than iron-based structures, so the roll can carry large forces and absorb sudden shocks. High Strength Alloy Cast Steel Rolls are therefore a standard choice for the stands where deformation is heaviest.
AS65I is positioned at 35-45 HSD, a moderate hardness chosen to protect toughness. Alloying keeps nickel low, at 0.2-0.5%, so strength comes from the alloyed steel matrix rather than from heavy nickel additions.
The practical outcome is a roll that is hard to break, forgiving of irregular stock, and economical to run in the stands that work hardest.
The alloyed steel body carries heavy separating forces and bending loads, keeping the roll stable during large reductions.
The toughness of cast steel reduces the chance that a bite shock or an off-center billet turns into a fractured roll, protecting both equipment and schedule.
Long contact with hot slabs, blooms, and billets raises roll temperature. The grade keeps its shape and strength under these conditions.
Even wear and resistance to deformation help the roll hold its barrel and groove geometry, so rolled stock leaves the stand with consistent shape.
Fewer unplanned stops, longer intervals between changes, and moderate material cost combine into a favorable cost per ton.
The grade serves a broad family of roughing duties:
Deep grooves and heavy, uneven loading in rail and section breakdown stands call for strength and groove stability.
Early stands convert billets into intermediate sizes, and a tough roll keeps this primary reduction steady.
Thick slabs enter at high temperature, so breaker and rougher rolls need strength and heat tolerance above all.
Wide barrels carry heavy loads, and consistent roll shape supports uniform plate thickness across the width.
Backup rolls transmit large forces, and edger rolls withstand side contact with the slab, both favoring a strong, tough body.
Barrel diameter, hardness within 35-45 HSD, and groove or surface design should be set according to mill type, stand position, and billet size. In each of these roughing roles, High Strength Alloy Cast Steel Rolls provide a dependable foundation for the line.
Cast steel has lower carbon, so it is tougher and more resistant to breakage but less wear-resistant. Adamite and iron grades trade some toughness for longer surface life, so the right choice depends on how severe the impact is.
Yes, for most roughing duty. Roughing stands lose more rolls to breakage and spalling than to gradual wear, so toughness is given priority over high hardness.
Even cooling, proper alignment, controlled billet temperature, and regular surface checks all help. These practices let High Strength Alloy Cast Steel Rolls give their full service life.