We use cookies to offer you a better browsing experience, analyze site traffic and personalize content. By using this site, you agree to our use of cookies. Privacy Policy
Home / Product / Infinite Chilled Hard Cast Iron Roll Grade V (ICV) for Finishing Work Roller

Infinite Chilled Hard Cast Iron Roll Grade V (ICV) for Finishing Work Roller

Return to product list

PRODUCT INTRODUCTION

Infinitely Chilled Hard Cast Iron Rolls V (ICV) are made from a high nickel-chromium-molybdenum alloy that is extremely hard and wear-resistant to withstand heavy loads and high-wear environments. It has good thermal conductivity and heat dissipation, can dissipate heat evenly, prevent local overheating of the roll body, reduce thermal deformation and thermal stress, and improve rolling accuracy. It has anti-adhesion properties, which can reduce the adhesion of steel billets to the roller surface, reduce surface roughness, and improve the quality of rolled products. It has good spalling resistance, which can prevent the roll surface from spalling and improve the dimensional accuracy, surface finish, and consistency of rolled products. ICV rollers reduce rolling costs by reducing roll replacement frequency, reducing energy consumption, and reducing scrap rates. Infinitely chilled hard cast iron roll V for finishing work rolls is a high-performance, high-reliability roll that can significantly increase roll service life, improve rolled product quality, reduce rolling costs, and improve production efficiency.

Hardness HSD: 77-85

Nickel composition %: 3.01-4.8

Suitable for racks: refined and rolled

Contact Us

PRODUCT SPECIFICATIONS

Infinite Chilled Rolls (IC)

Chemical Composition %
Symbol C Si Mn P S Cr Ni Mo V W Nb
ICⅡ 2.90-3.60 0.60-1.2 0.40-1.20 ≤0.25 ≤0.08 0.70-1.20 1.01-2.00 0.20-0.60
ICⅢ 2.90-3.60 0.60-1.2 0.40-1.20 ≤0.25 ≤0.08 0.70-1.20 2.01-3.00 0.20-1.00
ICⅣ 2.90-3.60 0.60-1.5 0.40-1.20 ≤0.10 ≤0.05 1.00-2.00 3.01-4.80 0.20-1.00
ICⅤ 2.90-3.60 0.60-1.5 0.40-1.20 ≤0.10 ≤0.05 1.00-2.00 3.01-4.80 0.20-2.00 0.20-2.00 0.00-2.00 0.00-2.00

 

Prosperities & Application
Symbol Hardness Tensile Strength Application
HSD MPa
ICⅡ 55-72 ≥160 Plate mills, temper mills, hot strip mills.
ICⅢ 65-78 ≥350
ICⅣ 70-83 ≥350
ICⅤ 77-85 ≥350

 

 

The Top of the Hardness Scale

ICV sits at the high-hardness end of the infinite chill family, with a working hardness of 77-85 HSD. It is built for the stands at the end of a finishing line, where a roll's job is no longer to break down thick stock but to protect the final size and surface of the product. In that role, ICV Cast Iron Finishing Mill Rolls are valued for holding their face for as long as the mill allows.

Nickel at 3.01-4.8% works with chromium and molybdenum to keep the structure fine and uniform through the working layer. Hardness at the surface is high, but it declines gradually with depth, so regrinding between campaigns exposes working metal rather than a soft interior.

High hardness is a deliberate trade. The grade gives up some impact tolerance in exchange for wear life and surface stability, which is the right bargain only where loads are steady and the strip is thin and uniform.

Performance Advantages

Surface quality at the finish line

The final stand sets the surface that customers see. A very hard, dense roll face resists roughening, so the polished condition lasts well into the campaign.

Dimensional stability

Very slow wear and low thermal distortion keep the roll profile close to target. Gauge and flatness stay predictable, and fewer corrective adjustments are needed during the run.

Clean running

The surface resists the sticking of hot steel, which would otherwise leave marks on the product and force early roll changes.

Consistency from coil to coil

Even wear and a stable surface condition mean the first product and the last product in a campaign are alike. That consistency reduces scrap and downgrades.

Lower total cost

Longer campaigns, fewer changes, and less scrap lower the cost per ton rolled, which can offset the roll's higher alloy content.

Finishing Stand Applications

ICV is meant for work rolls in finishing positions:

Last and near-last stands

Where final gauge and surface are fixed, wear resistance matters more than impact resistance. This is the primary position for the grade.

Thin, uniform stock

Steady loads and good strip shape suit a very hard roll. Rolling thick, irregular, or cold-ended stock risks overloading it.

Quality-driven product lines

Lines producing material with strict surface or flatness requirements benefit most, since the roll protects exactly what the customer measures.

Barrel size, hardness within 77-85 HSD, and surface finish should be set according to stand position, product, and cooling practice. For lines of this kind, ICV Cast Iron Finishing Mill Rolls provide a stable base for consistent output.

Q&A

Q1: Is 77-85 HSD too hard for my mill?

Not if the stand sees steady loads and good strip entry. Very hard rolls need careful handling: avoid cold-end entry, sudden overload, and thermal shock. Where those risks are higher, a lower-hardness grade is safer.

Q2: How should the roll be cared for?

Warm up before rolling, keep cooling even, and keep guides and alignment correct. Regrind on schedule, removing enough material to clear surface fatigue. These steps help ICV Cast Iron Finishing Mill Rolls reach their full campaign length.

Q3: How does ICV differ from lower-hardness infinite chill grades?

ICV targets wear and surface stability in the final stands, while lower-hardness grades give more tolerance for impact and suit earlier positions. The choice depends on where the roll sits in the line.

Send Us a Message

We'll get back to you within 24 hours with a tailored solution for your rolling mill.
captcha